FAQ Answer
When Bandung refuels happen at informal roadside pumps with handwritten receipts, how should a fleet operator reconcile those entries against a fuel drop alert before escalating it?
First, anchor the alert in time. Write down the vehicle, the exact time the alert landed, and the size of the reported drop. Then match that timestamp back to the ignition cycle, trip, or park it belongs to. This matters more than it sounds, because many setups damp small fuel movements so the alert does not fire on every dip during stop-start city driving and long waits at loading bays. That damping can push a real drop back by one reading window, which means the morning report may describe fuel that left the tank overnight. Verify the actual latency of your own setup in the fuel performance monitoring configuration instead of assuming it behaves instantly.
Second, gather whatever written record exists for that window. Informal roadside pumps rarely issue printed receipts, so you are often working with a handwritten slip, a phone photo, a driver note, or a message with a rough time and a rough amount. Collect it anyway. A partial record still narrows the window, even when the amount is uncertain. Note the driver-reported refuel time separately from the sensor timestamp rather than blending them into one figure. You want two timelines you can compare, not one that hides the disagreement.
Third, compare the driver-reported time against the fuel sensor trend. A refuel should show as a rise in the fuel line, and roughly when the driver says it happened. If the rise appears but the log does not have it, you are probably looking at a late entry, not a loss. If the log has a refuel but the sensor line never rose, question either the amount recorded or the condition of the sender. While you are in the configuration, confirm the tank size matches the real tank. Some units report fuel as a share of a set tank size rather than in litres, and a wrong tank value quietly rescales every drop you read. A gap that looks alarming can shrink or grow purely because of that setting.
Fourth, rule out the ordinary causes before treating the gap as diesel loss. Slope parking is a common one, because a vehicle sitting on an incline can read low, though it will not always do so. Sensor drift after a rough stretch of road is another. Look at location history alongside the fuel line for the same window. A steady fall while parked reads differently from a drop that coincides with a particular road section or a long idle at a loading bay.
Fifth, decide what kind of problem you have. If the refuel happened but was logged late or logged incompletely, that is an accounting fix, not a security escalation. Correct the record, note who refilled and roughly how much, and close the item with a reason. Only when the gap survives all of this do you open a reconciliation item, and when you do, give it a named owner and a next-step deadline. An alert that was acknowledged and closed with no fuel entry made looks handled on paper, but the record now shows a control gap.
Finally, plan for the shared site. When several vehicles refuel at the same roadside pump on one shift, run a site-level check rather than five separate investigations. One missing receipt often explains several alerts at once. Keep acknowledgement and accounting as two distinct steps on every shift, because the alert only compares against what the log says.
Related FAQs: How can you tell if your fleet is being spoofed versus just jammed?
Support Context
Why this answer matters
This FAQ is sourced directly from our support database. It helps teams deploy GPSController faster, reduce onboarding friction, and understand platform compatibility for real-world fleet operations.
Answer summary
Start with one rule and hold to it: a fuel drop alert is a delta reading, not a theft verdict. The unit compares fuel level from one ignition cycle to the next and flags a fall steeper than the threshold you allowed in your configuration. N...
Who it helps
- Fleet managers validating device compatibility
- Operations teams planning installation workflows
- Support teams troubleshooting GPS platform setup
- Platform-ready guidance for GPS devices and integrations
- Clear operational steps for setup and troubleshooting
- Updated answer content aligned with live deployments
Key terms
GPS tracking, fleet management, device installation, protocol setup, connectivity validation, and GPSController compatibility.
Implementation checklist
- Confirm device model, firmware, and protocol version
- Validate SIM coverage and network band support
- Map required sensors and IO configuration
- Test live device reporting before full rollout
Ideal use cases
- Fleet tracking, cold-chain monitoring, and asset recovery
- Compliance audits and safety analytics
- Fuel monitoring and route optimization
- Driver behavior insights and incident response
How to apply this
Collect device specs and confirm integration requirements.
Align configuration with GPSController platform rules.
Run a pilot test and scale across the fleet.
Related FAQs
When should I consider upgrading my fleet tracking system to prevent spoofing?
You should consider upgrading when you can't trust location data for core operations like verifying deliveries or getting reliable geofencing alerts for importa...
Can GNSS spoofing affect multiple vehicles in a fleet simultaneously?
Yes, absolutely. A powerful transmitter near your yard or depot can drown out real GPS signals for every vehicle and tracker in the area, making it appear as if...
What are the main compliance risks for delivery fleets from GNSS spoofing?
GNSS spoofing makes your operational records fraudulent. This includes ELD logs for driver hours, geotagged proof-of-delivery documents, and route histories. If...
How can I distinguish between GNSS spoofing and normal GPS signal loss in my fleet?
Look for physically impossible data patterns. Spoofing often shows sudden huge location jumps, steady directional drift, or vehicles appearing in impossible loc...
Can GPS jamming detection software differentiate between natural signal blockage and active jamming?
Usually no. Most software cannot tell the difference between natural signal blockage (like a metal building) and active jamming. This often leads to false posit...
When should I replace my tracking system instead of just upgrading software?
Replace when your current hardware lacks RF sensing capability and you face high-theft risk or strict compliance needs. Software alone cannot generate the foren...
Answer Snapshot
Start with one rule and hold to it: a fuel drop alert is a delta reading, not a theft verdict. The unit compares fuel level from one ignition cycle to the next and flags a fall steeper than the threshold you allowed in y...



















