FAQ Answer
When route history shows a stop was late, how do you tell whether the cause was the plan (geofence or scheduling error) or data capture (buffered timestamps, coverage gaps) before raising it with a driver or customer?
Begin by pulling the four fields for that one stop: planned arrival, recorded arrival, planned dwell and recorded dwell. A delivery delay is simply the gap between the plan and the record. Write the numbers down side by side. If the vehicle reached the fence near the planned time but sat inside it far longer than planned, you have a dwell question. If it arrived late and left quickly, you have a travel question. That first comparison tells you where to look next, and it costs a minute.
Step two is the timestamp check. Ask whether each point carries the device time or the server arrival time. Those are not the same thing, and a buffer of points uploaded after a network gap can shift the record enough to invent a delay that never happened. Look at the minutes around the stop. Do the points arrive in a smooth sequence, or do several land in one burst? A burst tells you the timing is unreliable at that point, so the lateness figure needs a footnote, not a conclusion. This is the kind of detail that separates delivery delay proof from a guess.
Step three is the fence. Did the stop alert fire where the vehicle actually parked, or did it fire somewhere else, perhaps on the road outside a yard? A geofence drawn tighter than the real parking area will mark arrivals as late when the truck was fine. The fix is a known-route walk: drive a route you know, watch where the alert fires, and widen the radius until it lands on the real stopping spot. Repeat it once to confirm the change holds. If the alert still misses, you have a planning problem, and geofence accuracy belongs on your configuration list rather than your driver list.
Sometimes both signs appear on the same stop. Here is the tie-breaker. If the timestamps look stable and orderly, but the fence is too tight or the scheduled dwell was never realistic, treat it as a plan problem. If the fence sits correctly over the real parking area and the timestamps still jump, treat it as a capture problem and take it to your provider. Get that order wrong and you tune the wrong thing for weeks.
A brief scenario helps. One stop shows a 26 minute late arrival against the plan. The dwell matches. The points around the stop arrive in a single clump at 14:52, and the alert fired 300 metres short of the depot gate on a service road where drivers actually wait. Two signals, one record. The timestamps are unstable, so you cannot lean on the minutes. The fence is misplaced, so the arrival was flagged at the wrong place. Neither finding proves the driver was late, and neither proves they were on time. What you can say is that the plan and the capture were both weak at that stop, and the delay number should not be used in a customer conversation until both are fixed.
That last point matters for how you present findings. State what the data shows, state what it cannot settle, and avoid dressing up a gap as certainty. An exception that cannot be exported with its timestamps stays a conversation, not evidence, so make sure your system produces an exportable exception report before anything is shared outside the team. Keep a dwell time comparison in the same file so the numbers travel together. And be aware that no exported record is automatically accepted in a dispute; that depends on your jurisdiction and process, not on the software.
Finally, close the loop. Feed what you learn back into dispatch planning feedback so the schedule reflects real dwell times and real fences. That reduces repeat causes. It will not remove every delay, and saying so honestly is better than promising a clean sheet. Teams that want to see what a defensible history layer looks like often review fleet management software and realtime vehicle tracking options before deciding whether to reconfigure or replace, and GPS Controller's own documentation treats retention depth and playback granularity as the first things to test. Save the human question for last, and only when the data has cleared the plan and the capture.
Support Context
Why this answer matters
This FAQ is sourced directly from our support database. It helps teams deploy GPSController faster, reduce onboarding friction, and understand platform compatibility for real-world fleet operations.
Answer summary
Start with one rule: classify the cause on the single stop record before you talk to anyone. A late stop is a number, not a mood. The job is to work out which cause the data supports, and to say plainly when it supports none of them. Route...
Who it helps
- Fleet managers validating device compatibility
- Operations teams planning installation workflows
- Support teams troubleshooting GPS platform setup
- Platform-ready guidance for GPS devices and integrations
- Clear operational steps for setup and troubleshooting
- Updated answer content aligned with live deployments
Key terms
GPS tracking, fleet management, device installation, protocol setup, connectivity validation, and GPSController compatibility.
Implementation checklist
- Confirm device model, firmware, and protocol version
- Validate SIM coverage and network band support
- Map required sensors and IO configuration
- Test live device reporting before full rollout
Ideal use cases
- Fleet tracking, cold-chain monitoring, and asset recovery
- Compliance audits and safety analytics
- Fuel monitoring and route optimization
- Driver behavior insights and incident response
How to apply this
Collect device specs and confirm integration requirements.
Align configuration with GPSController platform rules.
Run a pilot test and scale across the fleet.
Related FAQs
For a Karol Bagh fleet owner, how should the engine-on idle threshold be set per vehicle class so that routine waiting at local loading points is not flagged as misuse, while genuine engine-on, no-distance blocks are still caught?
The honest starting point is that there is no universally correct number of minutes. Any figure quoted as a standard is really just a guess that happens to suit...
When a Connaught Place geofence exit alert arrives for a vehicle that should have been parked after hours, how should a fleet team reconcile the shift roster, fuel log and trip log, and in what order, to settle it as a documented late return or escalate it as unauthorised movement?
A geofence exit alert in Connaught Place is a boundary crossing recorded at a time the zone should have been quiet. It is not proof of misuse. The tracker repor...
In an Ikeja delivery fleet's post-incident trip playback, how should a fleet manager decide whether a suspicious gap in a vehicle's recorded route is routine upload lag or a real route deviation before raising concerns about the driver?
After a stolen-vehicle scare, the moment you sit down with the playback is not the moment you should reach a verdict about a driver. A gap in the recorded route...
How should a transport operator set escalation and acknowledgement rules so each alert reaches an accountable person before it gets dismissed?
The most reliable way to get escalation and acknowledgement rules right is to stop treating them as settings and start treating them as a small procedure you ca...
How should a fleet decide the duration window before a speed reading counts as a sustained overspeed event, so momentary spikes are ignored but real speeding is still caught and defensible to a reviewer?
The short answer is that you cannot pick a sensible duration window in the abstract. You pick it from your own trip data, after you understand how your devices...
When travel time analytics, idle reports, and fuel figures disagree, in what order should a transport operator reconcile them so fleet ROI numbers aren't built on a false baseline?
The short answer is to work backwards from the most reliable event you have, then move outward one layer at a time. Most teams do the opposite. They open the fu...
Answer Snapshot
Start with one rule: classify the cause on the single stop record before you talk to anyone. A late stop is a number, not a mood. The job is to work out which cause the data supports, and to say plainly when it supports...



















